Select language:

ROBATEC® PA 6

PA 6 | extruded polyamide


Characteristics: Tough and impact resistant even in cold temperatures, highly dynamic energy absorption capacity, good chemical resistance to organic solvents and fuels, excellent sliding characteristics, good wear resistance, high level of moisture absorption for increased impact resistance, not as low-stress as cast PA 6G, energy-elastic, shock and vibration reducing, good weather resistance, excellent machinability, good adherence properties, good weldability, low density, ability to withstand high mechanical stresses, little distortion under mechanical loads, high surface hardness

Excellent resistance to hydrocarbons, alkalis, grease, oil, fuels, ethers, esters, ketones
No resistance to halogens, mineral acids and certain organic acids, oxidants

Typical applications: PA 6 is a standard polyamide for a wide range of technical applications.
A series of special versions is also available for your individual application needs.

Properties

  • Suitable for use in temperatures below 0°C
  • Suitable for contact with food
  • High chemical resistance
  • High impact strength
  • Good adherence characteristics
  • Good weldability
  • Cost-effective standard plastic
  • High Shore hardness
  • Low adhesion
  • Little sliding wear
  • High wear resistance
  • High yield stress
  • High impact resistance and elongation at break
  • High level of stability
  • High level of rigidity
ROBA<strong>TEC</strong><sup>®</sup> PA 6 natural

ROBATEC® PA 6 natural

Polyamide 6, extruded

Semi-crystalline thermoplast | Technical plastic

 

Robatec PA 6 natural is a standard polyamide for a wide range of technical applications.

Details
ROBA<strong>TEC</strong><sup>®</sup> PA 6 black

ROBATEC® PA 6 black

Polyamide 6, black extruded

Semi-crystalline thermoplast | Technical plastic

 

Compared with standard types:

  • black, therefore UV stabilized
Details
no_pic_available

ROBATEC® PA 6 GC

Polyamide 6, cast, granulated, and then extruded

Semi-crystalline thermoplast | Technical plastic

 

Compared with standard types:

  • Higher impact resistance
  • Extrusion ensures cast quality even at thinner thicknesses
Details
no_pic_available

ROBATEC® PA 6 GC MO

Polyamide 6, extruded with molybdenum disulfide and carbon black

Semi-crystalline thermoplast | Technical plastic

 

Compared with standard types:

  • Improved UV resistance
  • Limited suitability for foodstuffs
  • Higher tensile strength
  • Higher rigidity
  • Reduced hardness
Details
no_pic_available

ROBATEC® PA 6 GF 30

Polyamide 6, extruded with glass-fiber reinforcement

Semi-crystalline thermoplast | Technical plastic

 

Compared with standard types:

  • Improved UV resistance
  • Improved dimensional accuracy
  • Limited suitability for foodstuffs
  • Poorer sliding behavior
  • Poorer wear characteristics
  • Higher tensile strength
  • Higher rigidity
  • Greater hardness
  • Lower impact resistance
  • Improved long-term characteristics
Details
no_pic_available

ROBATEC® PA 6 ESD 60

Polyamide 6, extruded with carbon fiber

Semi-crystalline thermoplast | Technical plastic

 

 

Compared with standard types:

  • Improved UV resistance
  • Improved dimensional accuracy
  • Limited suitability for foodstuffs
  • Poorer sliding behavior
  • Poorer wear characteristics
  • Higher tensile strength
  • Higher rigidity
  • Greater hardness
  • Lower impact resistance
  • Improved long-term characteristics
  • ESD suitability

 

Details
ROBA<strong>TEC</strong><sup>®</sup> PA 6 GF Vacu

ROBATEC® PA 6 GF Vacu

Polyamide 6, extruded with glass-fibers

Semi-crystalline thermoplast | Technical plastic

 

 

Compared with standard types:

  • Deep-drawing characteristics
  • Improved UV resistance
  • Improved dimensional accuracy
  • Limited suitability for foodstuffs
  • Poorer sliding behavior
  • Poorer wear characteristics
  • Higher tensile strength
  • Higher rigidity
  • Greater hardness
  • Lower impact resistance
  • Improved long-term characteristics

 

Details